Residential Pumps

Pumps of Tennessee

Pumps of Tennessee carries a long line of pumps, filters, water softeners, water filtration, and more. We have pumps for sewage, swimming pools, fountains, sprinkler systems, sumps, and much more.

 

Please take a look at some of our brands and selections.

Sewage Pumps

Keen Pump® KG(X)2

The KEEN PUMP KG(X)2 series centrifugal grinder pumps easily handle residential, light commercial or industrial sanitary waste, reducing it to a fine slurry. The KG(X)2 pump is designed for use in pressure sewer applications or any piping network.

The KG(X)2 grinder pump retrofits into many existing competitor pump installations.  The KG(X)2 pump operates with the same control panel and installation piping / rail system.

The recessed vortex impeller design of the KG(X)2 grinder pump provides troublefree, non-overloading operation over the entire performance curve. The KG(X)2 pump produces capacities to 52 gpm with heads to 122 feet.

The KG(X)2 series pump features:
• Interchangeable into Competitor Installations
• Dual Silicon-Carbide Shaft Seals
• Pressed-In Motor with Internal Overload Protection
• 3-Bearing Shaft Support
• Internal Moisture Detection
• Strong 2hp Motor, 1 Phase (208/230/240) Volt or 3 Phase (208/230/460) V

Keen Pump logo
Keen Pump 2hp

Myers® Cast Iron Submersible Sewage Pump

Key Features

  • Bearing and Mechanical Seal – Permanently lubricated for long life.
  • Overload Protection – Built-in thermal overload with automatic reset.
  • Stainless Steel Hardware – Allows for easy disassembly after extended service.
  • Applications:  Sewage and Wastewater Removal
  • Capacities:  135 GPM 510 LPM
  • Shut-off head:  29’ 8.8 m
  • Operation: Tethered::  On: 20” 508 mm | Off: 11” 279.4 mm
  • Solids handling:  2” 50.8 mm
  • Intermittent liquid temp:  130°F 55°C
  • Motor:  1/2 and 3/4 HP, 1725 RPM, 115 or 230 Volt, single-phase, 60Hz. Oil-filled. Permanent split capacitor. Built-in thermal overload protection with automatic reset.
  • Acceptable pH range:  6-9
  • Shaft seal:  Type 6A or equal, Buna-N elastomers, silicon carbide seal faces, stainless steel metal parts.
  • Motor housing:  Cast Iron
  • Volute case:  Cast Iron
  • Impeller:  Cast Iron Vortex
  • Power cord:  Single phase: 20’ oil and water resistant 3 wire 16-3 SJTW-A/SJTW with UL listed integrally grounded three-prong plug.
  • Discharge, NPT:  3”
Myers Pumps
Keen pump

Flotec® Cast Iron Submersible Sewage Pump

  • BODY CONSTRUCTION:  Cast Iron
  • HORSEPOWER:  3/4
  • MAXIMUM CAPACITY:  170 GPM
  • FLOW AT 10′ LIFT:  125 GPM
  • SWITCH TYPE:  Tethered
  • SWITCH ON LEVEL:  7-1/2″
  • SWITCH OFF LEVEL:  3″
  • MINIMUM SUMP DIAMETER:  18″
  • MINIMUM SUMP DEPTH:  30″
  • DISCHARGE PIPE SIZE:  2″ NPT
  • MINIMUM PIPE SIZE:  2″ for sewage applications, 1-1/2″ for effluent applications
  • MAXIMUM SOLID HANDLING SIZE:  2″
  • CORD LENGTH:  10′
  • AMP DRAW:  9 amps
  • VOLTAGE:  115v, 60 Hz
  • RECOMMENDED BREAKER:  15 amp
  • LIQUID TEMP RANGE:  32°F-70°F (0°C-21°C)
  • AGENCY LISTING:  CSA and CUS
  • ACCESSORIES INCLUDED:  none
Flotec Logo
Flotec Pump

Water Treatment

Impression Series® Water Softeners

Soft water will change your life.

Get the clear, soft water you want. Impression Series® water softeners solve hard water challenges. Day and night, your water will now perform like it should — creating rich lathers with less soap, rinsing cleaner without film or residue. Plus your appliances will perform at peak, your clothes and towels will be softer, and your hair will be silkier!

  • Meter monitors and self-adjusts regeneration cycles based on household trend of water consumption
  • Easily programmed for optimum performance
  • Solid-state microprocessor control
  • Easy to read LED screen with user friendly console
  • Flexible “adjustable cycle sequence” programming — saves salt and water
  • Advanced history and diagnostic screens and lithium battery backup
  • Features an optional weather cover for outdoor installations
Impression Series
Impression Series

Sanitizer Plus Series®

A new level of intelligence in water treatment.

Sanitizer Plus Series® water treatment systems combine patented self-chlorinating technology* with advanced electronics to perform like four units in one – softening, removing iron and manganese, and raising low pH levels. This advanced system also controls odors caused by nuisance bacteria and minor sulfur conditions. Watch how it works!

  • Exclusive Crystal-Right media to remove hardness, iron, and manganese, plus it corrects low pH and control odor
  • Patented self-chlorinating technology* for bacteria odor control
  • Single unit operation — no chemicals or added equipment
  • Visual and audible “Check Salt” indicator
  • Extended lithium battery backup
  • Overrun capacity protection
  • Flexible “adjustable cycle sequence” programming — saves salt and water
  • Advanced history and diagnostic screens
  • Features an optional weather cover for outdoor installations

*Patent No. 6,726,817

Sanitizer Plus
Sanitizer plus

Pool/Sprinkler Pumps

Berkeley® Upstaged 4” Submersible Pumps

The Signature 2000® pump design has been delivering dependable performance since 1990. Our floating stage design continues to handle even the most aggressive water with our SignaSeal™ system that breaks down debris and reduces locking. Now we’re going further by upstaging and adding additional features to the 4″ submersible pumps you’ve grown to trust and rely on every day!

Resources

  • SUCTION/DISCHARGE MATEIAL:  MS: 300-Grade Stainless Steel / JP: Nylon 610 (Composite)
  • SCREEN TYPE:  MS: Serviceable / JP: Integrated
  • SCREEN MATERIAL:  MS: 300-Grade Stainless Steel / JP: Nylon 610
  • CABLE GUARD MATERIAL:  MS: 300-Grade Stainless Steel / JP: PVC
  • CABLE GUARD ATTACHMENT METHOD:  MS: 2 screws – 300-Grade Stainless Steel and 2 hooks / JP: 2 screws – 300-Grade Stainless Steel and bottom inserts into suction slots
  • CABLE GUARD SCREW PLACEMENT:  MS & JP: Discharge/Shell area
  • SHELL MATERIAL:  MS & JP: 300-Grade Stainless Steel
  • SHELL CONSTRUCTION METHOD:  MS: Threaded, left handed threads / JP: Sealed
  • SHELL THICKNESS:  MS: .065″ / JP: .032″
  • SHELL SERVICEABLE:  MS: Yes / JP: No
Berkeley

Myers® PQP Series Centrifugal / Sprinkler Pump

Quick priming PQP Series Pump feature lightweight construction in a self-priming design. These models offer a stronger pump body with reinforcement ribs and also a new 2″ suction that is designed for the professional pump contractor

Key Features
  • BODY CONSTRUCTION: Fiberglass-reinforced polypropylene
  • HORSEPOWER: Available in 1, 1-1/2, and 2 HP
  • MAXIMUM CAPACITY: 90 GPM (model PQP25)
  • FLOW at 10′ LIFT and 30 PSI: 44 GPM (model PQP15)
  • MAX LIFT: 25′
  • MAXIMUM DISCHARGE PRESSURE: 60 PSI (model PQP25)
  • MAXIMUM TOTAL PRESSURE (Inlet + Pump Pressure): PQP10: 105 PSI / PQP15: 110 PSI / PQP20: 120 PSI / PQP25: 140 PSI
  • SUCTION SIZE: 1 & 1-1/2 HP: 1-1/2″ NPT 2 & 2-1/2 HP: 2″ NPT
  • DISCHARGE SIZE: 1 & 1-1/2 HP: 1-1/2″NPT 2 & 2-1/2 HP: 2″ NPT
  • AMP DRAW (full load): Model & Voltage Dependent
  • VOLTAGE: Switchable 230v/115v on 1 & 1-1/2 HP models, 230v on 2 HP
  • MAXIMUM WATER TEMPERATURE: 140 F (60 C)
  • BASE: High-impact composite, ABS
  • SEAL PLATE: Fiberglass-reinforced, Polypropylene
  • IMPELLER: Polycarbonate
  • DIFFUSER: Polycarbonate
  • SHAFT: Stainless Steel
  • CLAMP: Stainless Steel
Myers Pumps
Myers Sprinkler Pump